²úÆ·Ðͺţº(Avago:HFCT-711XPD£¨Ìæ»»ÐͺÅ:FTCX-M131X-02Dxx£©
²úÆ·ÐÎò£ºHFCT-711XPD Multi-rate 1310 nm XFP 10 Gbit/s Optical Transceiver
¼æÈÝÆ·ÅÆ£ºAvago
Ô­³§ÐÎò£ºHFCT-711XPD Multi-rate 1310 nm XFP 10 Gbit/s Optical Transceiver

HFCT-711XPD Multi-rate 1310 nm XFP 10 Gbit/s Optical Transceiver

Description
The 1310 nm XFP transceiver is a high performance, cost effective module for serial optical data communications applications specified for signal rates of 9.95 Gb/s to 10.5Gb/s. It is compliant to XFP MSA Rev 4.5. The module is designed for single mode fiber and operates at a nominal wavelength of 1310 nm. The transmitter section incorporates a directly modulated 1310 nm distributed feedback laser (DFB). The receiver section uses an MOVPE grown planar SEDET PIN photodetector for low dark current and excellent responsivity. Integrated Tx and Rx eye openers provide high jitter-tolerance and low jittergeneration and transfer for full XFI and SONET compliance. The internally ac coupled high speed serial I/O simplifies interfacing to external circuitry. The electrical interface is made using an industry standard 0.8 mm pitch 30-pin right angle connector. Optical connection is made via the duplex LC connector.

Features

Compliant to XFP MSA
Multi-protocol multi-bitrate compliant
Compliant to SONET/SDH OC-192/STM-64 rate 9.9532Gb/s, Telcordia GR-253-CORE SR-1, ITU-T G.691 I64.1
Compliant to IEEE 802.3ae 10GBASE-LR for 10GbE,10.3125 Gb/s
Compliant to 10GFC 1310 nm Serial PMD, type 1200-SM-LL-L, 10.51875 Gb/s
Compatible with 10.7Gb/s and 11.3Gb/s operation for FEC functionality
Uncooled 1310 nm DFB Laser and PIN Photodiode
Compliant XFI 10G Serial electrical interface
LC Duplex optical connector interface conforming to ANSI TIA/EIA604-10 (FOCIS 10)
1.5W typical power dissipation
Superior Thermal and EMI performance to support high port densities
Customizable clip-on heatsink to support a variety of line card environments
-5 to +70 °C case operating temperature range
Capable of extended temperature (-10°C to +85°C, Case temperature) operation**
Hardware pins are available for the following control signals:
- Transmitter disable
- Module power down/reset
- Receiver loss of signal
- Module not ready
- programmable interrupt
2-wire serial management interface provides real time monitors of:
- Transmitted Optical Power
- Received Optical Power
- Laser Bias Current
- Module Temperature
- Supply Voltage
- Laser Temperature
Link Lengths up to 10 km with 9 µm SMF
IEC 60825-1 Class 1/CDRH Class 1 laser eye safe

Note:
** Long term reliability at elevated temperatures is not guaranteed”

Applications
Fiber Channel Switches
Host Bus Adapter Cards
Mass Storage System and Server I/O
Optical Cross Connect Switches
Next generation SONET/SDH ADMs
Core Routers

The product offers digital diagnostics using the 2-wire serial interface defined in the XFP MSA. The product provides real time temperature (module and laser), supply voltage, laser bias current, laser average output power and received input power. The digital diagnostic interface also adds the ability to disable the transmitter (TX_DIS), power down the module, monitor for module faults and monitor for Receiver Loss of Signal (RX_LOS). Transmitter disable, interrupt, power down/reset, receiver loss of signal and module not ready are also hard wired pins on the 30-pin right angle connector.

Important Notice

Performance figures, data and any illustrative material provided in this data sheet are typical and must be specifically confirmed in writing by F-tone Networks before they become applicable to any particular order or contract. In accordance with the F-tone Networks policy of continuous improvement specifications may change without notice.The publication of information in this data sheet does not imply freedom from patent or other protective rights of F-tone Networks or others. Further details are available from any F-tone Networks sales representative.