尊龙凯时人生就是搏

±ê×¼¹âÄ£¿é

±ê׼ЭÒé¹âÄ£¿é

¼æÈÝЭÒé¹âÄ£¿é

ÆäËüÖÖÀà¹âÆ÷¼þ

ÊÖÒÕÖ§³Ö

6G 2km SFP+ Transceiver

6G 2km SFP+ Transceiver

0.0/5 rating (0 votes)

Description

Description

FT-MTRS-6E21-01is a high performance, cost effective modules, which is supporting Multi Rate 1.25-6.25Gbps, and transmission distance up to 2km on SM fiber. The transceiver consists of two sections: The transmitter section incorporates a 1310nm FP Laser and a driver. The receiver section consists of a PIN photodiode integrated with a transimpedance preamplifier (TIA) and a Limitting Amplifier. The module is hot pluggable into the 20-pin connector. The high-speed electrical interface is base on low voltage logic, with nominal 100 Ohms differential impedance and AC coupled in the module.

 The optical output can be disabled by LVTTL logic high-level input of TX_DIS. Transmit Fault (Tx_Fault) is provided to indicate that the module transmitter has detected a fault condition related to laser operation or safety. Loss of signal (RX_LOS) output is provided to indicate the loss of an input optical signal of receiver. A serial EEPROM in the transceiver allows the user to access transceiver monitoring and configuration data via the 2-wire SFP Management Interface. This interface uses a single address, A0h, with a memory map divided into a lower and upper area. Basic digital diagnostic (DD) data is held in the lower area while specific data is held in a series of tables in the high memory area.

Features 

¡ñ  Up to 2km transmission distance

¡ñ  Support  Multi Rate 1.25-6.25 Gbps

¡ñ  1310nm FP and PIN receiver

¡ñ  SFI electrical interface

¡ñ  2-wire interface for integrated Digital Diagnostic monitoring

¡ñ  SFP+ MSA package with duplex LC connector

¡ñ  Hot pluggable

¡ñ  Very low EMI and excellent ESD protection

¡ñ  +3.3V power supply

¡ñ  Power consumption less than 1.2W

¡ñ  Operating case temperature: -40~+85°C

Applications

¡ñ  High-speed storage area networks

¡ñ  Computer cluster cross-connect

¡ñ  Custom high-speed data pipes

¡ñ  LTE optical repeater application

Compliance

¡ñ  Compliant with Fiber Channel(FC)-Standard INCITS 352

¡ñ  Compliant with IEEE 802.3ae-2002

¡ñ  Compliant with FCC 47 CFR Part 15, Class B

¡ñ  Compliant with FDA 21 CFR 1040.10 and1040.11, Class I except for deviations pursuant

Specification

Absolute Maximum Ratings

Parameter

Symbol

Min.

Max.

Unit

Storage Temperature

TS

-40

+85

¡æ

Supply Voltage

VCC3

0

3.6

V

Relative Humidity(Non-condensing)

RH

-

85

%

Rx Input Average Power

Pmax

-

+3

dBm

Recommended Operating Conditions

Parameter

Symbol

Min.

Typical

Max.

Unit

Operating Case Temperature

TC

-40

25

+85

¡æ

Power Supply Voltage

VCC3

3.13

3.3

3.47

V

ICC3

-

-

345

mA

Power Dissipation

PD

-

-

1.2

W

Data Rate

-

-

6.25

Gbps

Transmission Distance

-

-

2

Km

Transmitter Operating Characteristic-Optical, Electrical

Parameter

Symbol

Min.

Typical

Max.

Unit

Note

Centre Wavelength

λC

1260

1310

1355

nm

Note1

Laser Off Power

Poff

-

-

-30

dBm

Average Optical Power

Pavg

-8.2

-

0.5

dBm

Note1

Extinction Ratio

ER

3.5

-

-

dB

Transmitter Dispersion Penalty

TDP

-

-

3.2

dB

Relative Intensity Noise

Rin

-

-

-128

dB/Hz

Optical Return Loss Tolerance

12

-

-

dB

Operating Data Rate

1.25

-

6.25

Gbps

Optical Eye Mask

Compliant with IEEE 802.3ae

Single Ended Output Voltage Tolerance

-0.3

-

4

V

Common Mode Voltage Tolerance

15

-

-

mV

Tx Input Diff Voltage

VI

180

-

700

mV

Tx Fault

VoL

-0.3

-

0.4

V

At 0.7mA

Data Input Total Jitter

TJ

-

-

0.28

UI

Notes:

[1] Average optical power shall be measured using the methods specified in TIA/EIA-455-95.

Receiver Operating Characteristic-Optical,Electrical

Parameter

Symbol

Min.

Typ.

Max.

Unit

Note

Center Wavelength

λr

1260

1310

1355

nm

Receiver Sensitivity in Average Power

Psens

-

-

-14.4

dBm

LOS Assert

LosA

-30

-

-

dBm

LOS Deassert

LosD

-

-

-16

dBm

LOS Hysteresis

LosH

0.5

-

-

dB

Overload

Pin

0.5

-

-

dBm

Receiver Reflectance

-

-

-12

dB

Operating Data Rate

1.25

-

6.25

Gbps

Single Ended Output Voltage Tolerance

-0.3

-

4

V

Rx Output Diff Voltage

Vo

550

-

850

mV

Rx Output Rise and Fall Time

Tr/Tf

-

34

-

ps

20% to 80%

Total Jitter

TJ

-

-

0.7

UI

Control and Status I/O Timing Characteristics

Parameter

Symbol

Min.

Max.

Unit

Note

TX Disable Assert Time

t_off

100

µs

Note1

TX Disable Negate Time

t_on

2

ms

Note2

Time to initialize

t_init

300

ms

Note3

TX Fault Assert Time

t_fault

1

ms

Note4

TX Fault Reset

t_reset

10

µs

Note5

LOS Assert Time

t_loss_on

100

µs

Note6

LOS Deassert Time

t_loss_off

100

µs

Note7

Serial ID Clock Rate

f_serial_clock

100

kHz

Notes:

[1] Time from rising edge of TX Disable to when the optical output falls below 10% of nominal

[2] Time from falling edge of TX Disable to when the modulated optical output rises above 90% of nominal

[3] From power on or negation of TX Fault using TX Disable

[4] Time from fault to TX fault on

[5] Time TX Disable must be held high to reset TX_fault

[6] Time from LOS state to RX LOS assert

[7] Time from non-LOS state to RX LOS deassert.

 

 

 

 

Important Notice

Performance figures, data and any illustrative material provided in this data sheet are typical and must be specifically confirmed in writing by F-tone Networks before they become applicable to any particular order or contract. In accordance with the F-tone Networks policy of continuous improvement specifications may change without notice.

The publication of information in this data sheet does not imply freedom from patent or other protective rights of F-tone Networks or others. Further details are available from any F-tone Networks sales representative.

Search

sitemap¡¢ÍøÕ¾µØͼ