+86-028-85255257
Description
FT-MTRQ-4S100 transceiver is a Parallel 40Gb/s Quad Small Form-factor, Hot-Pluggable optical module.
The module integrates 4 independent transmitters and 4 independent receivers inside. Four-channel 850nm VCSEL array, PIN array£¬amplifier and Driver are used in the module for compact size, low power consumption and low cost. Each channel can operate at 10Gbps up to 100m using OM3 fiber, and 150m using OM4 fiber.
The transceiver is compliant to the industry standard SFF-8436 QSFP+ Transceiver Specification. Digital diagnostic functionsis provided to monitor the working state of the module. The electrical interface uses a 38 contact edge type connector. The optical interface uses an 8 or 12 fiber MTP (MPO) connector.
FT-MTRQ-4S100 transceiver features small size, parallel multi- channel, hot-pluggable, low power and high speed operation. It’s very suitable for high speed short-distance density data connections such as 40G BASE-SR4, InfiniBand QDR, Switch& Route interconnects etc.
Features
¡ñ Compliant to the industry standard SFF-8436 QSFP+ Transceiver Specification
¡ñ 4* 10.3125Gbps per module, bi-directional operation
¡ñ 5 DDM with MPD monitor
¡ñ High reliability 850nm VCSEL array transmitter
¡ñ Hot pluggable
¡ñ Single 3.3V power supply, Low power consumption
¡ñ 0 to 70°C case temperature operating range
¡ñ RoHS-6 compliant (lead-free)
Applications
¡ñ 10GBASE-SR &40GBASE-SR4 40G Ethernet InfiniBand QDR (4 x 10G), DDR (4 x 5G) and SDR (4 x 2.5G) interconnects
¡ñ Datacom/Telecom Switch & Router connections
¡ñ High speed multi-channel parallel data connections
Compliance
¡ñ IEEE802.3ba 40GBASE-SR4
¡ñ SFF-8436 QSFP Specification
¡ñ InfiniBand Architecture QDR Specifications
Absolute Maximum Ratings |
|
|
|
|
|
|
Parameter |
Symbols |
Min |
Typical |
Max |
Unit |
Notes |
Storage Temperature |
TSTG |
-40 |
- |
+85 |
ºC |
|
Operating Temperature |
Top |
0 |
|
70 |
|
|
Operating Relative Humidity |
RH |
5 |
- |
85 |
% |
|
3.3V Supply Voltage |
VCC |
-0.5 |
- |
+3.6 |
V |
|
Recommended Operating Conditions |
|
|
|
|
|
|
Parameter |
Symbols |
Min |
Typical |
Max |
Unit |
Notes |
Case temperature |
Tc |
0 |
- |
+70 |
¡æ |
|
3.3V Supply Voltage |
VCC |
3.135 |
3.3 |
3.465 |
V |
|
Data Rate |
|
|
41.25 |
|
Gbps |
|
Receiver Differential Data Output Load |
|
|
100 |
|
Ohms |
|
Logic Input Voltage High |
Vih |
2 |
|
Vcc+0.3 |
V |
|
Logic Input Voltage Low |
Vil |
-0.3 |
|
0.8 |
V |
|
Two wire Serial Interface Clock Rate |
|
|
100 |
400 |
KHz |
|
Power Supply Noise |
|
|
|
50 |
mVpp |
|
Fiber Length(OM3 2000MHz*Km) |
|
0.5 |
|
100 |
m |
|
Fiber Length(OM44700MHz*Km) |
|
0.5 |
|
150 |
m |
|
Important Notice
Performance figures, data and any illustrative material provided in this data sheet are typical and must be specifically confirmed in writing by F-tone Networks before they become applicable to any particular order or contract. In accordance with the F-tone Networks policy of continuous improvement specifications may change without notice.
The publication of information in this data sheet does not imply freedom from patent or other protective rights of F-tone Networks or others. Further details are available from any F-tone Networks sales representative.